Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Atlas Gutter Replacement: The Austin Owner’s Guide
Replacing Atlas gutters in Austin typically runs $9 to $16 per linear foot installed, with most single-story homes landing between $1,400 and $2,600 for a full replacement. We stock Atlas-compatible gutter components on our trucks, so most replacements happen in a single visit. You usually find out your gutters have failed the hard way: after a Hill Country downpour, water is spilling over the front edge, pooling at your foundation, or you spot a section sagging away from the fascia board.
We’re an independent Austin roofing and gutter contractor, not a division of Atlas. We install and replace Atlas gutter systems because they hold up well in Texas heat, but when we say “Atlas replacement” we mean we’re matching the profile and gauge to what’s already on your home, using either Atlas-branded sections or a like-for-like equivalent that fits the existing brackets and downspouts.
Which Atlas Models This Applies To
Atlas gutters come in two profiles that account for the vast majority of Austin installations: 5-inch K-style and 6-inch half-round. The K-style is the workhorse, with the flat back and decorative front that mimics crown molding. The half-round shows up more often on older homes in neighborhoods like Hyde Park and Travis Heights, where the original architectural style leans traditional.
The compatibility gotcha most homeowners miss: Atlas 5-inch K-style gutters use a specific bracket spacing of 24 inches on center, and the end caps are crimped rather than snapped. If a previous contractor patched a section with a generic big-box brand, the profile lip won’t match, and you’ll get leaks at the seams. That’s why we measure the width across the top opening and check the bracket pattern before quoting a replacement. It takes five minutes and keeps us from installing the wrong part on your house.
On the OEM versus aftermarket question: Atlas-branded gutters come in 0.027-gauge aluminum, which is a nice middle weight. You can buy 0.019-gauge sections off the shelf at a home center for less money. They’ll dent the first time a ladder leans against them and they’re more likely to pull loose at the screws during a windstorm. We’ll install either if you ask, but we’ll tell you up front that the thinner stuff doesn’t earn its savings in Central Texas.
Styles & brands we work with
Signs Your Atlas Gutter Replacement Is Failing
- Water spilling over the front lip during rain. This usually means the gutter is undersized for the roofline or the downspouts are clogged. If it happens on a roof with Atlas shingles that shed water fast, undersized gutters just can’t keep up.
- Seams leaking at the corners or end caps. Atlas K-style gutters are sectional, and the sealant at those joints breaks down after about 8 to 10 years in Austin’s heat. You’ll see water streaks down the fascia board under the seams.
- Sagging sections with visible gaps at the brackets. The screws backing out of the fascia, or the wood softening behind them from repeated moisture exposure. Every sagging section is a section about to drop.
- Rust bleeding through the paint at the bottom of the gutter. Even aluminum can show oxidation when the factory finish wears thin. By the time you see rust stains, the metal underneath is pitting.
- Water pooling near your foundation after heavy rain. That’s not always a gutter failure, but if the downspouts are clear and water still ponds at the slab edge, the pitch of the gutter run has likely shifted and the water is exiting at the wrong point.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full Atlas-compatible gutter replacement in Austin, expect $9 to $16 per linear foot installed. A standard 1,600-square-foot single-story home has roughly 140 to 170 linear feet of gutter, which lands the job between $1,400 and $2,600. Two-story homes with harder access run higher, usually closer to $13 to $18 per foot because of ladder work and fall-safety setup.
That price includes removal and disposal of the old gutters, new fascia brackets, new downspouts, sealed seams, and a slope check so water actually moves toward the downspouts. The number we quote is the number you pay. No change order because we “found something” once the old gutters came down. If we find rotted fascia behind the gutter, we’ll document it with photos, show you exactly what we’re seeing, and give you a separate written price before touching it.
Every gutter replacement we install carries our 365-Day Done Right Promise in writing. If a seam opens up or a bracket pulls loose within a year, we come back and fix it at no charge. That includes the second visit, no negotiation over whose fault it is.
| Item | Typical Austin Price |
|---|---|
| 5-inch K-style gutter, installed | $9 – $14 per linear foot |
| 6-inch half-round gutter, installed | $12 – $16 per linear foot |
| Downspout replacement | $40 – $80 per 10-foot section |
| End cap replacement | $25 – $50 per cap, installed |
| Fascia board replacement (if rotted) | $4 – $8 per linear foot |
| Gutter guard add-on | $3 – $6 per linear foot |
DIY or Call Us?
Gutters are one of the few exterior systems where a careful homeowner can handle a simple repair, and we’ll tell you that straight. Swapping a bent end cap or re-securing a loose bracket with a longer screw: if you have a ladder, a drill, and a tube of gutter sealant, that’s a Saturday morning job.
Where DIY goes wrong is replacing a full run or re-pitching a section. Gutters need a consistent slope of about 1/4 inch per 10 feet toward the downspout. Too much pitch and water rushes past the downspout. Too little and it pools, collecting Austin’s oak leaves and granule runoff from your Atlas shingles until the whole section sags. Getting that pitch right while on a ladder at roofline is the part that separates a twenty-year gutter from a two-year one. And ladder work near power lines or a steep roofline is where we’d rather you not take the risk. Call (254) 587-6371 and we’ll put eyes on it.
FAQs
Atlas aluminum gutters last 18 to 25 years in Central Texas, provided the seams are re-sealed roughly every 8 to 10 years and the downspouts stay clear of oak leaves. The heat does more damage than the rain, as it breaks down sealant and causes the aluminum to expand and contract against the brackets. If you’re at year 18 and seeing recurring leaks at the seams, replacement begins to make more sense than another round of patching. Call (254) 587-6371 for a pricing breakdown on your specific roofline.
Yes, if the damage is isolated to a seam, an end cap, or a bracket. But if you have multiple failing seams, visible rust-through, or more than one sagging section, the cost of repair often approaches 40 to 50 percent of a full replacement, and you’re still left with aging metal everywhere else. We’ll give you both prices in writing and let you decide. We’re fine either way.
A standard single-story Atlas-compatible gutter replacement takes one day for most Austin homes. Two-story homes or longer runs can stretch to a day and a half. You’ll get a written arrival time before we head your way, and before-and-after photos of the work are included in your digital invoice.
We carry 5-inch and 6-inch Atlas-compatible sections, matching end caps, brackets, and downspout elbows on our trucks, so most replacements happen without a second trip. For color-matched sections on less common finishes, we may need a day to pull them from our supplier. We’ll tell you before you commit to anything, so there’s no surprise delay.
Written by Dylan Pace, Owner, Crestview Roofing Co Austin at Crestview Roofing Co Austin, serving Austin and nearby areas.